1Pellet stoves user manuallcd english
10HOT AIR DUCTINGThe pipe destined for ducting the hot air must have an internal diameter of 80 mm, be insulated and protected from heat loss.INsTAll
11sOUveNIR The “Souvenir” model can be ducted on the rear, on the side or on the top; for further information on installation, refer to the instructi
12emmA plUs AND TOsCA plUs The Emma and Tosca Plus models also oer the option to decide where to direct the hot air ow, thanks to two gate valves co
OFF13CONTROL BOARDBUTTON ON/OFFDISPLAY OF VARIOUS TEXT MESSAGESTO ACCESS THE MENUTEMPERATURE SETTING OPERATING POWER ADJUSTMENT ENGLISHDISPLAY ICONSIn
OFF22261 43256666622222222222222222123456214GENERAL MENUSET CLOCKSET CHRONOLANGUAGEUSERTECHNIC SETRESERVED TO THE QUALIFIED TECHNICIANYEARMONTHDATEM
15If the remote control is o because it has no batteries, stove can be controlled from the control panel on top of it.While replacing the battery, pa
16COMMISSIONING SETTINGSOnce the power cable at the back of the stove has been connected, move the switch, also located on the back, to (I).The switch
OFF17FUNCTIONING AND LOGICIGNITIONOnce the points listed previously have been checked, press key 1 for three seconds to ignite the stove. During the
18PELLET FEED ADJUSTMENTThe following menu allows the adjustment of pellet feed as a percentage.If the stove has functioning problems owing to the qua
19CONTROLS PROCEDURE Press the key 6, SET CLOCK will appear. Press key 2 several times until "USER" is displayed Press key 6. "
20 ENGLISHSTBY FUNCTION SET TO OFF FACTORY SETTINGIf the Stby function is not active (OFF), if the stove reaches the room temperature set, it will g
21CHRONOThe chrono allows to program 4 time spans within a day to use every day of the week. The switch-on and switch-o time can be set in every time
22*2ND TIME PERIOD SWITCHONAt this point, the second time period must be programmed.The sequence to be followed is the same and is repeated as for th
23CLEANING UNDER USER'S RESPONSIBILITYSome images could be oset from the original model.DAILYBurn pot: remove the burn pot from the relevant com
AFEEACDEFB24ROUTINE MAINTENANCE In order to guarantee proper functioning and safety of the device, the operations indicated below must be performed ev
25DisplaysDisplay ReasonoffStove ostaRtThe start phase is in progresspellet feeDingThe feeding of the pellet during the ignition phase is in progress
26alaRMsDisplay explanation solutionIndicates the presence of an alarm.On: indicates the presence of an alarmO: indicates the absence of alarmsFlashi
27ENGLISHWARRANTY CONDITIONSEXTRAFLAME S.p.A., with oces in via dell’Artigianato 12 Montecchio Precalcino (VI), guarantees this product for 2 (two) Y
28ENGLISH ALL PARTICULARS SUBJECT TO NORMAL WEAR ARE NOT COVERED BY WARRANTY:This category includes: The gaskets, all ceramic or toughened glass, co
31
index3We thank you for having chosen our company; our product is a great heating solution developed from the most advanced technology with top quality
EXTRAFLAME S.p.A. Via Dell’Artigianato, 12 36030 - MONTECCHIO PRECALCINO (VI) - ITALY +39.0445.865911 - +39.0445.865912 - info@ex
4WARNINGSThe instruction manual is an integral part of the product: make sure that it always accompanies the appliance, even if transferred to other o
5SAFETY DEVICESSAFETY DEVICES KEY: * = PRESENT, = NOT PRESENTSTOVESCircuit board: intervenes directly by sending the product into alarm condit
6RADIATION AREAArea immediately near the hearth in which the heat caused by combustion is diused, where no combustion materials must be present.REFLU
BCAS< 3 m3 - 5 %7CHIMNEY OR INDIVIDUAL FLUEThe chimney or individual ue must respond to the following requisites: seal the combustion products,
< 3 m45°45°50 cm< 5 m> 5 m< 5 m50 cmH minβ>A<A>50 cmZ8External pipethat is isolatedInspectionInspectionAppliance connection to th
9CONNECTION TO EXTERNAL AIR INLETSThe appliance must be able to use the necessary air to guarantee regular functioning through external air inlet. The
Commenti su questo manuale